How to make a tile floor shine? Tiles are the most sought-after flooring solution in most homes due to their attractive and shiny appearance. However, tile floors eventually lose their shine over time due to wear, stains and dirt. And such dull floors can make the whole room look old and outdated. So, instead of ignoring those dull floors, make sure to give them a new life and restore them to their former shiny glory. Read Here: Best Cordless Vacuum For Pet Hair- The Ultimate Guide
So, how to make a tile floor shine? Here’s some quick tips to help you with!
1) Sweep and Vacuum
First off, you need to start by sweeping and vacuuming your tile. Both are important and together they help in removing the debris and dirt that has built up on your tiles. You can simply sweep your tile floors lightly then vacuum them afterward. Using the brush roller of your vacuum is fine since it won’t scratch your floor.
Tile is not concrete or stone— rather it is a porous clay that has been hardened. However, it is still prone to damage, and loose dirt can scratch and damage it permanently. So, light sweeping and vacuuming can pull off the damaging dirt off your tile flooring.
2) Use Natural Solutions To Clean
Once you removed all large particles from your tile floor, it is time to start a deeper clean of your tile to make it shinier. Although you can use the more powerful chemical cleaning solutions you bought from the grocery store, they are not that safe and cost a lot of money.
Use natural ingredients instead.
- Soapy Water
Most of the time, a soap and water solution is enough when mopping your tile flooring. Mopping should be done every now and then in order to prevent dust and dirt buildup on the floor.
Make sure the mop is wrung thoroughly before using it on your tile flooring. In addition, you should change the solution once it becomes dirty. When there are tough stains, a sponge or a soft brush can be used to gently scrub the spot.
After that, the entire floor should be rubbed with a soft towel in order to absorb the soap solution. It can also be rinsed with clean water, if necessary.
- Vinegar Solution
A natural kitchen product, vinegar can be used to disinfect and clean stained or soiled tile floorings. Unlike chemicals, vinegar can effectively clean your soiled tile flooring without the harsh fumes.
Also, once it dries up, vinegar also leaves a natural and fresh scent.
To use vinegar when cleaning a tile floor, mix a small amount with warm water. Dip the mop into the vinegar solution and mop thoroughly, allowing the floor to air dry. When tough stains occur, sprinkle the still wet tile with baking soda, scrubbing it with a rag before wiping it again with the mop solution.
- Ammonia + Water
Ammonia is a great ingredient to make your tile flooring bright and shiny. Also, it can be used to remove dirt and stains from the tile floors.
Mix a bit of ammonia with warm water and use a mop to clean and disinfect your tile floor. Just make sure to rinse off the ammonia solution with clean water in order to remove any lingering solution.
- Baking Soda
Widely used in cooking, baking soda is also an all-around cleaning solution. In particular, baking soda can be used to remove tile tough grout and tile stains if your floor appears to be discolored and dirty. As a matter of fact, baking soda is considered as a natural tile polisher, rejuvenating your tile floors.
In order to use it, combine an equal amount of warm water and baking soda in order to create a thick paste. Using a soft-bristled brush, gently scrub your grout and tiles. Then allow the solution to sit for at least 10 minutes then rinsing with warm water.
Consider repeating the process to remove the tougher and more obvious stains on tile floors.
- Vinegar + Ammonia + Borax
Now, for the toughest dirt scum buildup on your tile floor, you can fight it off and return its former shine by combining powerful cleaners.
Mix ½ cup ammonia, ½ cup white vinegar, ¼ cup borax, and 1-gallon warm water. Use this cleaning solution to mop your tile floor or spray on the soiled surface. Rinse the floor well and allow it to air-dry.
- Dish Soap + Rubbing Alcohol + Vinegar
A great cleaning agent for tile floors, especially porcelain, dish soap is not that powerful so it will not damage your flooring. However, if you need some power, adding rubbing alcohol and vinegar should do the trick.
Just mix ¼ cup rubbing alcohol, ¼ cup vinegar, 1teaspoon dish soap, and 1-gallon warm water. Then, use it to mop the floor or spray onto the floor. Just be careful not to scrub too much since you will create lots of suds. This will require you a couple of rinses.
- Riccar Vacuum Reviews: Top 3 Picks in 2020
- Shark vs Dyson Vacuum Comparison
- 10 Best Vacuum for Hardwood Floors and Carpet
- The Bissell Air Ram 1984 Review
- Best Car Vacuum for Pet Hair: Top 5 Editor’s Picks
3) Adding High Gloss Tile Sealer
Now, once you cleaned your tile floors, a high gloss tile sealer can be applied in order to give it an extra shiny boost. Also, a high gloss tile sealer should help protect your flooring and keep it looking great for longer.
High gloss tile sealers come in various types so make sure to choose one that is specifically designed for the type of tile you have. The majority of high gloss sealers are suitable for stone tiles with porous surfaces instead of ceramic tiles. Read Here: 10 Vacuum Cleaning Tips for Your Floors
Not, make sure to test the high gloss sealer first on sample tile first in order to make sure that it bonds well, especially for ceramic tiles since this can cause issues. Take note, however, that a topical sealer can fade or become scratched over time. Thus, you will need to reapply it again for shiny and attractive tile flooring.
Dirt, dust and pet dander are transferred to the tile floor. When this dirt accumulates and neglected, your once gorgeous and shiny tile flooring becomes dull, dirty and unattractive.
Thus, it is important to keep your floors clean to maintain its shine. And by using the methods mentioned above, you can make your tile floorings not only squeaky clean but also attractively shinier than ever before!